SRS Airbag Module Reset Archives

SRS Airbag Meaning

Do you know what the meaning of SRS airbag is? If not, let me fill you in.

SRS is an abbreviation for supplementary, or secondary, restraint system. This is what the airbag system is, and it consists of the actual airbags, the impact sensors, the seat belts, and the SRS airbag control module.

When the airbag light pops up on a dashboard, this means that there is something wrong with the airbag system and that the airbags will not deploy until that problem is dealt with. Resetting the SRS airbag module or purchasing a brand new one can solve the problem. Of course, the latter option is much more expensive. Therefore, attempting to reset the module on your own is probably your best bet.

To do this, you first want to locate the unit in your vehicle. Generally, airbag modules can be found underneath the driver’s seat. Then you want to disconnect your battery and move your steering wheel so that you can remove all the hardware on the driver airbag module. You want to make sure that all the wiring, horn wiring, grounding strap, airbag connectors, and radio wired are completely disconnected. Then proceed by removing the module. After opening it up, search for the 8-pin SMD EEPROM chip. Solder some 32-gauge hookup wires to connect the airbag module to a serial port EEPROM reader. The crash data can then be analyzed. Replace all the values from the crashed chip with the values found on the virgin chip. Then rewrite this into your computer in order for the hard codes to be eradicated. After that, you can replace the unit back into your vehicle. Your SRS airbag light should turn off and your airbags should be working properly again.

Of course, if the instructions above seem too difficult for your liking, you can send your unit in to the company Safety Restore. They will reset your SRS airbag module to factory settings and will not charge an arm and a leg for it either!

How to reset the airbag module after accident

If you have a vehicle with a faulty SRS airbag module, you might know that it needs to be replaced. You may be thinking that you do not have enough money to buy a totally new SRS unit at the dealer. Lucky for you, that is okay. There are plenty of instructions online detailing how you can remove the unit from your vehicle and reset it back to factory condition yourself! You just need to have the proper tools and software to do so.

Let me fill you in on the process. First, you should remove the unit from your vehicle. Most likely, it is located underneath the driver seat or the front passenger seat. You can then begin disassembly of the module. You should open up the module and search for the 8-pin SMD EEPROM chip. This is what stores all the crash data. You then need to solder some 32-gauge hookup wire to connect the airbag module to a serial port EEPROM reader. After that, you can analyze the crash data. Different types of software are available to read the EEPROM chip, but all essentially do the same job. At last, you can finally replace the airbag module computer. Replace all the values from the crashed chip with the ones from the virgin chip and rewrite it into the computer. That way, the hard codes that were present can be cleared. The final step would be to replace the module into your car and check if you were able to successfully reset it. Within 6 seconds, your SRS light should go off. Your vehicle’s tech-stream software can also be checked to see that there are no more codes or faults present.

Of course, if the entire process seems too difficult, or you do not want to risk doing the job improperly, you can send it in to a company that specializes in just that. A perfect example of such a company is Safety Restore. Visit safetyrestore.com and purchase the SRS airbag module reset service for a very affordable price.

Video – How to reset the airbag module after accident

Can you reset the airbag module?

The airbag module is a key component of a vehicle. It controls the supplemental restraint system in your car including the airbag sensors, seat belt pre-tensioners, and the inflators. In addition, it acts as a storage box for hard codes and crash data when your vehicle is involved in a collision.

When a vehicle is involved in a crash that deploys the airbags, crash data and hard codes are automatically stored in the unit. Only a reset or buying a brand new unit will allow a driver to have a properly functioning airbag module. Many people choose to purchase a new module at the dealer, but this comes with a hefty price tag. Others choose to reset it at home. You certainly can remove the SRS airbag module from your vehicle and reset the unit to factory settings, you just need to have the right tools and follow the steps correctly in order to succeed in resetting it properly.

To begin the process, you need to remove the SRS airbag module from your vehicle. Generally, it can be found underneath the driver’s seat but sometimes its location varies to underneath the front passenger seat, in the center console, kick panel, behind the steering wheel, or under the radio. To access the module, the bottom half needs to be removed. After it has been removed, the disassembly process can begin. When you open up the unit you need to look for the 8-pin SMD EEPROM chip that stores all the crash data. You should then solder some 32-gauge hookup wire to connect the unit to a serial port EEPROM reader. The next step would be to analyze the crash data. There are different types of software available that can read from the EEPROM chip. After analyzing, you can finally replace the airbag computer. Replace all the values from the crashed chip with those from the virgin chip and rewrite it into the computer so that the hard codes can be cleared. The final step would be to place the unit back into your vehicle and check if the reset was a success. Within just 6 seconds, your SRS light should go off. You can also check with your vehicle’s tech-stream software to see that there aren’t any faults or codes present.

Of course, if you do not want to purchase the tools and software necessary for the reset and still risk not having it reset properly, there is another alternative. You can turn to the company Safety Restore for a guaranteed reset.

Video – Can you reset the airbag module?

How to Test your Airbag Module

You probably already know by now the functionality of the SRS airbag module in your vehicle and its overall importance in preserving your safety on the road. You know that the SRS airbag module is responsible for tying in the entire airbag system including the airbags themselves, the impact sensors, and even the seat belt pre-tensioners. Without the airbag module working properly, none of these parts can function individually the way they are intended to. This means that if your car is involved in a crash, the airbags will not deploy which can result in serious injury or even death. For this reason, you know how crucial it is to get a brand new module—or your previous one reset—immediately after it becomes faulty or has stored crash data. If you go with the latter option, getting the reset is one thing. Testing to see if the reset was a success is another. Below are the steps you should take to test your airbag module and see that all previous crash data and hard codes have been erased. The process is quite simple.

To begin, you need to reinstall the airbag module into your vehicle. Make sure all the wiring that was disconnected in the initial disassembly process is reconnected. Then you can reconnect your car’s battery. After that, just turn on your car and take a look at the airbag light found on the instrument panel of your console. If the airbag module reset was a success, the airbag light should dim out within approximately 7 seconds. If the light fails to turn off, you may need to bring the unit to a professional company or contact your local dealership. The company Safety Restore specializes in SRS airbag module resetting, and can definitely be trusted if you see that you were unsuccessful in completing the job yourself.

How to test your SRS airbag module.

Where is the airbag module located?

Wondering where your airbag module is located in your vehicle?

An airbag control module is the mechanism that controls the airbag system. There are several airbags in a vehicle, some located in the front, on the sides, or on knee-level to passengers. However, there is only one SRS airbag module unit in a vehicle. The location of the airbag module differs from vehicle to vehicle depending on the make and model of it. In some vehicles, it is located in the center console, kick panel, under the radio, or behind the steering wheel. Generally, though, it can be found underneath the driver’s seat or front passenger’s seat. Heavy-duty vehicles such as buses and trucks have engine control modules instead of airbag control modules. These units are often located beneath the instrument panel glove box on the front-passenger side of the vehicle.

Find out where your airbag module is located.

The importance of an airbag module cannot be stressed enough. It makes the workings of the entire airbag system possible. When a sudden stop or collision occurs, the airbag module receives information from the impact sensor that then passes on a signal to deploy the airbags. Without a properly functioning airbag module in a vehicle, the airbags wouldn’t even deploy. After airbag deployment, the airbag sensor is locked until it is replaced or completely reprogrammed.

Following a crash, the information stored in the airbag module in the form of hard codes and crash data can prove quite useful—and is usually admissible in court too. Everything from seat belt use, engine and vehicle speed, brake light switch position, throttle position, impact speed change, airbag deployments and seat belt pre-tensioner deployments are stored in this small unit. Those who analyze car accidents often look at the airbag module information and find it more beneficial than other physical evidence or verbal explanation.

If you yourself have been involved in an accident, refrain from buying a brand new module. Instead, have your present unit restored to factory settings by the company Safety Restore.

When to Replace Your Airbag Module

When to replace your airbag module.

If you do not know what an airbag module is or what it does, you most likely do not know when you need to replace it. For your own safety’s sake, it is important to learn, so let me fill you in.

The SRS airbag module in your vehicle is a tiny unit generally located beneath the driver or front passenger seat. Even though the unit is relatively small, it serves a big role in preserving occupants’ safety on the road. This is because the entire airbag system—which includes the airbags themselves, the impact sensors, and seat belt pre-tensioners—depends on the SRS airbag module. Without a properly functioning module, or without one altogether, the airbags would not be able to deploy during an accident. As you can imagine, that can result in a greater possibility of injury or even death.

Wondering when to replace your airbag module? – This is what a SRS module looks like.

When a vehicle has been involved in an accident, the SRS airbag module picks up the information during the crash such as the vehicle and engine speed, seat belt use, throttle position, seat belt pre-tensioner deployments, impact speed change, airbag deployments, and brake light switch position. All this information is stored in the form of crash data and hard codes. When the unit has all that stored data in it, it is an indication that it needs to be replaced. This would be the proper time to purchase a brand new SRS airbag module or reset the present unit back to factory settings. Otherwise, the airbags will not be able to serve their purpose in the future.

You probably won’t want to replace the unit entirely at the dealer knowing that you have an equally safe—and more affordable—alternative. You can send the unit in to a company that specializes in resetting SRS airbag modules: Safety Restore.

Can you drive without an airbag module?

While a vehicle can still run without an airbag module, it is strongly recommended that drivers do not operate the vehicle without it being installed—unless an emergency situation arises and there is no other option. There are several reasons for this, the biggest being to preserve one’s safety while driving.

The main reason why it is unsafe to drive without an SRS airbag module installed is because a car’s airbags will not work without them. If they do no work, then they are not able to serve their purpose as secondary restraint systems—and as a result will not deploy if an accident were to occur. As you can imagine, that can pose as a giant problem. Without airbags deploying, a driver and any passengers can face serious injury or even death. During a sudden stop or a collision, the airbags are what stop the occupants of a vehicle from crashing through the windshield or against other objects and people in the vehicle. Without airbags in the equation, nothing would be able to slow down occupants’ change in momentum and reduce the forces exerted on them.

The safest bet for an owner of a vehicle that needs their SRS airbag module replaced is to have another form of transportation ready for the time it takes to reset or entirely replace the unit. Although it may be a hassle to do so, it is better to be safe than sorry.

The great thing is that there is a company—Safety Restore—that is able to reset airbag modules and only takes 24 hours to do so. For that short amount of time, arranging another form of transportation shouldn’t even be a problem. Not only will it take a short amount of time but it can also save a driver hundreds or even thousands of dollars compared to the prices at the dealer!

4 New Year’s Resolutions You Can Pick Up This Year

New Year means New YOU! With everyone else making New Year’s resolutions, it can’t hurt for you to do the same. Even if you think you won’t be able to accomplish them, there are bound to be some that you definitely can. Read some of these suggestions below. Perhaps, you may even surprise yourself and be able to accomplish all of them!

One great New Year’s resolution is to eat healthier. Now, this can get difficult really quick if you let it. If you’ve been eating junk food for a greater portion of your life, it is hard to just get up and quit eating it completely. However, if you take the time to make small, gradual adjustments to your diet, you can end up very successful. For example, try substituting a bag of chips for a bag of delicious veggies and dip. Or, instead of indulging in a carton of ice cream with a whole bunch of unhealthy toppings, try eating frozen yogurt topped with fruit. Honestly, the possibilities for healthy substitutions are endless.

Another New Year’s resolution you can adapt to is incorporating a little fitness into your life. Diet and exercise are two key components of a healthy lifestyle, so why wouldn’t you want to strive for that? You don’t have to run an entire mile every day either. Try starting with a short walk around your neighborhood. If you feel like you can do more than that, certainly don’t hesitate. The more fitness and exercise you can fit into your day-to-day routine, the better! You can even grab a friend and have them join in on the fun.

Trying to be kinder and demonstrate more acts of kindness is another goal you can set for yourself for the New Year—or any day! They say kindness makes the world go round, and it really does. There are so many ways you can brighten someone’s day, whether it be a friend or a complete stranger. If you demonstrate more acts of kindness, it is likely that those on the receiving end will do the same and a ripple effect will follow. And what could be better than that?

Finally, a last New Year’s resolution you can set is to look at all your possessions and make sure they are working properly. Oftentimes, we do not take care of our things and once they break, we just replace them with brand new ones. This year, strive to keep your items well maintained so that they can function and last longer. This can apply to your clothes, your home, your furniture, and your car. Take the SRS airbag module in your vehicle for example. Make sure that it is functioning properly at all times. If you see that an OEM Airbag Module Reset is needed, get it done immediately. Things like OEM Airbag Module Resets shouldn’t be postponed. The airbag module is a very important component of your vehicle, and you want it to be working up to par every time you drive. At the company Safety Restore, you can get an OEM Airbag Module Reset for a very affordable price. Head on over to safetyrestore.com and see for yourself!

is needed, get it done immediately. Things like OEM Airbag Module Resets shouldn’t be postponed. The airbag module is a very important component of your vehicle, and you want it to be working up to par every time you drive. At the company Safety Restore, you can get an OEM Airbag Module Reset for a very affordable price. Head on over to safetyrestore.com and see for yourself!

How to wear a seat belt when pregnant

As many people know, seat belts reduce the risk of serious injury by about 50%. Therefore it is crucial for both drivers and passengers alike to wear one at all times. For women who are pregnant, wearing a seat belt correctly is especially important. Depending on the severity of the injury, being involved in a vehicular accident can increase the risk of serious pregnancy complication such as placental abruption, premature rupture of the membranes (PROM), preterm labor, miscarriage, or even stillbirth. Below are a few seat belt tips you should follow if you are pregnant.

#1. To begin with, you will probably be safest wearing a lap and shoulder belt combination, as this provides the most protection. Other belts can be worn too, but this type is recommended.

#2. The way the lap belt would be worn is below your belly, touching your thighs. It should be placed low and snug on your hips. Failing to wear it this way may result in less protection.

#3. Your belt should never be worn above or across your belly.

#4. You should always make sure to wear the shoulder belt snugly across the middle of your chest and shoulder.

#5. You should refrain from slipping the shoulder belt behind your back or beneath your arm at any time. Even though this is sometimes an impulsive thing to do for more comfort, remember that it will leave you less protected.

#6. If you are the driver, make sure your belly is situated a safe distance from the airbag. At least 10 inches should separate your breastbone from the dashboard or steering wheel. Of course, as your belly grows you may find yourself needing to move your seat back more to be seated safely.

#7. If your car has been recently involved in an accident, you want to make sure that your seat belts along with everything else in your car is still properly working. If your seat belts have deployed, your airbag module may have stored crash data and hard codes. For this, an airbag module reset would be necessary. The company Safety Restore provides airbag module reset services for only a fraction of the price a dealer charges! The quality is impeccable too. Get your airbag module reset at Safety Restore so that you and your belly could be driving safely.

Airbag Repair Centre

Ever wonder what the car seat laws are in Connecticut? If you live in the Constitution state, there are several things you should know about strapping your child into a car seat. This will ensure that you are driving safely and not endangering the lives of your children. Some of these rules may seem ridiculous to you as your child grows bigger, but they were established for a reason. Therefore, you should follow the precautions and do what the seat belt laws suggest.

First, it is important to note that Connecticut became the eighth state in the United States to accept the recommendations of the American Academy of Pediatrics in 2017. They followed the recommendation that young children should stay in rear-facing child restraints until the age of two. The age and weight requirements for the use of booster seats and car seats have also increased by Connecticut law. In order to outgrow a booster seat in Connecticut, a child must be eight years old and have a minimum weight of 60 pounds. This is meant to reduce the chances of injury or even death during intense acceleration or deceleration of a vehicle.

Under Connecticut law, all children under the age of two or weighing under thirty pounds must be strapped into a rear-facing child seat with a five-point harness.

Children between the ages of two and four, and weighing between thirty and thirty nine pounds, are required to be placed in either a forward-facing or rear-facing car seat with a five-point harness.

Children between the ages of five and seven, or weighing anywhere between forty and fifty nine pounds, must ride in a rear or forward-facing restraint held in by a lap and shoulder seat belt.

Any child or adolescent from the age of eight through fifteen years, who weighs sixty or more pounds, must use a government approved booster seat or a safety seat belt.

If you ever find your vehicle in an accident, your seat belts may deploy. This can give rise to crash data and hard codes being stored in your car’s SRS airbag module system. To ensure the safety of your passengers–including those strapped into car seats–it is crucial to take care of the problem immediately. You have the choice to go to a dealer to buy a new unit or turn to an airbag repair centre like the company Safety Restore. This latter option is much more reasonable. The SRS airbag reset service that this airbag repair centre provides costs only a fraction of buying a new unit at the dealer. Safety Restore also provides its customers with a lifetime warranty and performs the repairs in just 24 hours! What better airbag repair centre to turn to than Safety Restore?