{"id":36257,"date":"2026-11-21T09:56:03","date_gmt":"2026-11-21T09:56:03","guid":{"rendered":"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/"},"modified":"2026-11-21T09:56:17","modified_gmt":"2026-11-21T09:56:17","slug":"post-repair-scan","status":"publish","type":"post","link":"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/","title":{"rendered":"Post Repair Scan Steps for SRS Systems"},"content":{"rendered":"<p>A car can look finished, drive straight, and have a dark airbag lamp while the SRS module still holds crash data. Before you hand back the keys, treat the post repair scan as proof that the affected systems work and the repair-related faults are resolved, not as a button to make warning lights disappear.<\/p>\n<p>Start by matching the scan to the work order. A bumper repair may involve a camera or radar bracket; a seat removal can disturb an occupant sensor; a suspension repair can leave an ABS sensor disconnected. Scan the systems the repair could have affected, then keep the report that shows what the final check found.<\/p>\n<h2>Table of Contents<\/h2>\n<ul>\n<li><a href=\"#systems-a-post-repair-scan-must-clear\">Systems a Post Repair Scan Must Clear<\/a><\/li>\n<li><a href=\"#how-to-run-the-post-repair-scan\">How to Run the Post Repair Scan<\/a><ul>\n<li><a href=\"#set-up-before-clearing-anything\">Set up before clearing anything<\/a><\/li>\n<li><a href=\"#repair-clear-and-verify\">Repair, clear, and verify<\/a><\/li>\n<\/ul>\n<\/li>\n<li><a href=\"#soft-codes-hard-codes-and-what-to-clear\">Soft Codes, Hard Codes, and What to Clear<\/a><ul>\n<li><a href=\"#a-clear-command-isnt-a-repair\">A clear command isn&#039;t a repair<\/a><\/li>\n<li><a href=\"#stored-event-data-needs-a-real-fix\">Stored event data needs a real fix<\/a><\/li>\n<\/ul>\n<\/li>\n<li><a href=\"#documentation-that-shows-the-repair-holds\">Documentation That Shows the Repair Holds<\/a><ul>\n<li><a href=\"#verify-the-parts-not-just-the-report\">Verify the parts, not just the report<\/a><\/li>\n<\/ul>\n<\/li>\n<li><a href=\"#what-to-do-when-crash-data-remains\">What to Do When Crash Data Remains<\/a><\/li>\n<\/ul>\n<p><a id=\"systems-a-post-repair-scan-must-clear\"><\/a><\/p>\n<h2>Systems a Post Repair Scan Must Clear<\/h2>\n\n<figure class=\"wp-block-table\"><table><tr>\n<th>System<\/th>\n<th>Scan it when<\/th>\n<th>A pass looks like<\/th>\n<th>Common miss<\/th>\n<\/tr>\n<tr>\n<td>SRS and airbags<\/td>\n<td>Deployment, airbag lamp, or module removed<\/td>\n<td>No current or crash DTCs, and the lamp stays off after the bulb check<\/td>\n<td>Clearing the lamp while crash data remains<\/td>\n<\/tr>\n<tr>\n<td>Seat belt pretensioners<\/td>\n<td>Locked belt, fired charge, or webbing replaced<\/td>\n<td>Retractor locks and releases with no pretensioner circuit code<\/td>\n<td>Installing new webbing on a fired retractor<\/td>\n<\/tr>\n<tr>\n<td>Powertrain OBD<\/td>\n<td>Every collision car before delivery<\/td>\n<td>No repair-related codes; incomplete monitors have a drive-cycle plan<\/td>\n<td>Scanning SRS only<\/td>\n<\/tr>\n<tr>\n<td>ABS and stability control<\/td>\n<td>Suspension, wheel, or sensor work<\/td>\n<td>No active wheel-speed or yaw codes after a short road test<\/td>\n<td>Leaving a sensor unplugged during body work<\/td>\n<\/tr>\n<tr>\n<td>Occupant classification<\/td>\n<td>Seat removed or weight sensor disturbed<\/td>\n<td>Passenger airbag status matches an empty and an occupied seat<\/td>\n<td>Skipping the occupant classification system after seat R&amp;I<\/td>\n<\/tr>\n<tr>\n<td>12-volt supply<\/td>\n<td>Before any scan<\/td>\n<td>Voltage is stable under scan conditions, with no low-voltage warning<\/td>\n<td>Scanning on a dying battery<\/td>\n<\/tr>\n<\/table><\/figure>\n<p>Mark the rows that match this repair order before connecting the tool. A deployed airbag always puts both SRS and seat belts on the list. The belt may have a fired pretensioner or a locked retractor even if the webbing looks usable; replacing webbing alone doesn&#039;t prove the mechanism is ready. If belt work is part of the repair, check the matching <a href=\"https:\/\/www.safetyrestore.com\/seat-belt-repair-service\/62-seat-belt-buckle-pretensioner.html\">seat belt buckle pretensioner service<\/a> against the specific fault and component involved.<\/p>\n<p>The table is a scope check, not a substitute for inspecting what was disturbed. If a seat came out, include occupant classification and inspect its connectors. If suspension or wheel work took place, include ABS and stability control. A wheel-speed sensor that was unplugged for access can leave a fault even when the mechanical work is correct.<\/p>\n<p>A light bumper job still merits a scan when a camera, radar unit, or its bracket moved. The warning may not appear immediately, and a bracket that looks straight isn&#039;t proof that the sensor is aimed correctly. Follow the vehicle&#039;s repair procedure for any required calibration as well as scanning.<\/p>\n<p>Check the battery before scanning. Low supply voltage can trigger faults that weren&#039;t caused by the collision repair, making the report harder to interpret. Stabilize the supply first, then distinguish genuine repair issues from faults caused by power loss.<\/p>\n<p>Use the powertrain row even when the work was confined to the body. A scan limited to SRS can miss a repair-related code in another module. Mark each applicable row on the work order; that gives the technician a defined scope and makes it harder to overlook a system because its warning lamp is off.<\/p>\n<p><a id=\"how-to-run-the-post-repair-scan\"><\/a><\/p>\n<h2>How to Run the Post Repair Scan<\/h2>\n<p>A post repair scan is the electronic sign-off after collision or SRS work. It&#039;s different from the pre-repair scan, which records the vehicle&#039;s faults before parts come off. The post-repair report should show what&#039;s present after the repair, what was corrected, and whether a fault has returned.<\/p>\n<p>Use a scan tool that can access SRS and airbags, communicate with every vehicle module, and save a report with the vehicle identification number, date, and mileage. A basic powertrain code reader won&#039;t cover that job. Connect the tool according to its instructions and the vehicle&#039;s procedure; don&#039;t assume a generic reader&#039;s \u201cno codes\u201d screen means every system was checked.<\/p>\n<p><figure class=\"wp-block-image size-large\"><img decoding=\"async\" src=\"https:\/\/www.safetyrestore.com\/blog\/wp-content\/uploads\/2026\/11\/post-repair-scan-repair-process.jpg\" alt=\"A five-step infographic explaining how to conduct an automotive post-repair scan for vehicle safety and quality assurance.\" \/><\/figure><\/p>\n<p><a id=\"set-up-before-clearing-anything\"><\/a><\/p>\n<h3>Set up before clearing anything<\/h3>\n<ol>\n<li><p><strong>Stabilize power and inspect grounds.<\/strong> Support the battery so voltage stays stable with the engine off. Check the main grounds for loose or disturbed connections. A weak supply can produce communication faults that distract from the repair issue you&#039;re trying to verify.<\/p>\n<\/li>\n<li><p><strong>Identify the vehicle and work performed.<\/strong> Record the year, make, model, mileage, and the modules, seats, and restraint components that were disconnected. This gives the report context and helps the next technician understand why a connector or module might have logged a fault.<\/p>\n<\/li>\n<li><p><strong>Connect an SRS-capable, all-module scanner.<\/strong> Use ignition on and engine off unless the tool or vehicle procedure directs otherwise. Confirm the scanner identifies the vehicle correctly and can access the restraint and other relevant modules.<\/p>\n<\/li>\n<li><p><strong>Run the first all-module scan and save it unedited.<\/strong> Keep the report before erasing anything. It captures the codes the vehicle still has at that point, which may include a connector left unplugged during reassembly or a clock spring that hasn&#039;t been reconnected.<\/p>\n<\/li>\n<\/ol>\n<p><a id=\"repair-clear-and-verify\"><\/a><\/p>\n<h3>Repair, clear, and verify<\/h3>\n<ol start=\"5\">\n<li><p><strong>Diagnose faults before using the clear command.<\/strong> Read the code details and match them to the work. If the report shows an open seat connector, inspect and reconnect it correctly. If a clock spring circuit is open, resolve that issue before treating the SRS as repaired. Clearing first destroys useful evidence and can leave the cause untouched.<\/p>\n<\/li>\n<li><p><strong>Clear only faults explained by completed work.<\/strong> A code that came from a disconnected component during repair may be appropriate to clear after that component is correctly reinstalled. A current circuit fault, deployment record, or unexplained code needs diagnosis, not an erase.<\/p>\n<\/li>\n<li><p><strong>Cycle the ignition and scan again.<\/strong> Turn the key off for at least thirty seconds, then switch it on and check the modules again. This gives modules a fresh opportunity to initialize and report whether the fault is still present. If a code returns, the repair hasn&#039;t passed that check.<\/p>\n<\/li>\n<li><p><strong>Road-test when the repair calls for it.<\/strong> A short, controlled road test can help confirm ABS and stability faults don&#039;t return and allow powertrain monitors to update. Follow the vehicle&#039;s procedure and road-test conditions. If a monitor remains incomplete, document the drive-cycle plan instead of presenting it as a completed result.<\/p>\n<\/li>\n<li><p><strong>Run the final scan and save the release file.<\/strong> Confirm the SRS lamp completes its bulb check and goes out, then check for current or returning faults across the relevant modules. Save the unedited final report as the release copy, alongside the untouched first scan.<\/p>\n<\/li>\n<\/ol>\n<blockquote>\n<p><strong>Shop rule:<\/strong> Keep the original scan and the final scan. One shows what the vehicle reported before clearing; the other shows whether the completed repair holds.<\/p>\n<\/blockquote>\n<p>A clean scan doesn&#039;t replace physical checks. Verify the repaired connectors are seated and that the parts removed for access are back in place. For restraint work, the <a href=\"https:\/\/www.safetyrestore.com\/seat-belt-repair-service\/85-seat-belt-repair-after-accident.html\">seat belt repair after an accident<\/a> must be confirmed at the belt itself, not inferred from a quiet scan screen.<\/p>\n<p><a id=\"soft-codes-hard-codes-and-what-to-clear\"><\/a><\/p>\n<h2>Soft Codes, Hard Codes, and What to Clear<\/h2>\n<p>The code most tempting to erase is the one that remains after the SRS lamp goes dark. That doesn&#039;t prove the repair is complete. A scan tool may turn off a warning or clear an erasable fault while crash data or a hard pretensioner fault remains stored.<\/p>\n\n<figure class=\"wp-block-table\"><table><tr>\n<th>Code type<\/th>\n<th>Typical example<\/th>\n<th>Scan tool can erase it<\/th>\n<th>Next action<\/th>\n<\/tr>\n<tr>\n<td>Soft or intermittent<\/td>\n<td>Low-voltage or loose connector fault<\/td>\n<td>Yes, after the cause is fixed<\/td>\n<td>Repair, clear, key-cycle, confirm it stays gone<\/td>\n<\/tr>\n<tr>\n<td>Non-crash history<\/td>\n<td>Old communication glitch<\/td>\n<td>Usually yes<\/td>\n<td>Note it, clear it, watch the rescan<\/td>\n<\/tr>\n<tr>\n<td>Communication after dead battery<\/td>\n<td>U-code from modules that lost power<\/td>\n<td>Often yes<\/td>\n<td>Stabilize voltage, rescan, then clear if gone<\/td>\n<\/tr>\n<tr>\n<td>Current circuit fault<\/td>\n<td>Open squib or resistance out of range<\/td>\n<td>No while the fault is active<\/td>\n<td>Repair wiring or the component before any clear<\/td>\n<\/tr>\n<tr>\n<td>Hard crash or deployment<\/td>\n<td>Stored crash event or fired pretensioner<\/td>\n<td>No<\/td>\n<td>Reset or repair the module or belt, install, then rescan<\/td>\n<\/tr>\n<\/table><\/figure>\n<p><a id=\"a-clear-command-isnt-a-repair\"><\/a><\/p>\n<h3>A clear command isn&#039;t a repair<\/h3>\n<p>Soft or intermittent faults often come from low voltage or a connector moved during body work. Once the cause is corrected, clear the fault, cycle the ignition, and confirm it stays gone. If it returns, don&#039;t keep erasing it; inspect the connector, wiring, and affected component.<\/p>\n<p>Non-crash history codes need a note in the file before you clear them. Communication codes after a dead battery may disappear once power is stable and the modules communicate again. Rescan first so you can tell whether the fault is still active rather than assuming the battery explains everything.<\/p>\n<p>Current circuit faults are different. An open squib circuit or a resistance reading the module rejects points to a problem that remains now. Don&#039;t clear that fault and release the car. Find the damaged wiring, poor connection, or defective component, correct it, then scan again.<\/p>\n<p><a id=\"stored-event-data-needs-a-real-fix\"><\/a><\/p>\n<h3>Stored event data needs a real fix<\/h3>\n<p>Consider a car with a replaced airbag and a used control module. The wiring scan may look clean, but the module can still hold the crash event from the previous deployment. The lamp being off after an erase doesn&#039;t establish that the module&#039;s stored event data is gone.<\/p>\n<p>The same caution applies to a fired pretensioner. New webbing doesn&#039;t restore a fired charge or prove that the retractor will protect an occupant. If the code names a crash, pretensioner, or stored event, stop clearing and service the affected part. Install the repaired or replacement component, then run the scan again.<\/p>\n<p><a id=\"documentation-that-shows-the-repair-holds\"><\/a><\/p>\n<h2>Documentation That Shows the Repair Holds<\/h2>\n<p>A scan is useful to the next technician only if the shop can show what the tool found. Save two PDFs per job: the untouched pre-repair scan and the final post-repair scan. Name each file with the last six characters of the VIN, the service date, and \u201cpre\u201d or \u201cpost,\u201d and make sure the first page identifies the mileage and scan tool.<\/p>\n<p><figure class=\"wp-block-image size-large\"><img decoding=\"async\" src=\"https:\/\/www.safetyrestore.com\/blog\/wp-content\/uploads\/2026\/11\/post-repair-scan-repair-documentation.jpg\" alt=\"A checklist infographic titled Documentation That Shows the Repair Holds, illustrating seven best practices for scanning documentation.\" \/><\/figure><\/p>\n<p>Before trim goes back on, take clear photographs of the seated connectors at the SRS module, each pretensioner, and the clock spring if it was disturbed. These pictures help show the connection work was completed and give the shop a reference if a code returns later. Keep the images with the job file, not as a substitute for the scan reports.<\/p>\n<p>On the final report, mark which codes were cleared and identify any code left in the system intentionally. Add a short explanation for each one. A note like \u201chistorical communication fault, did not return after rescan\u201d is more useful than a bare list of erased codes.<\/p>\n<p><a id=\"verify-the-parts-not-just-the-report\"><\/a><\/p>\n<h3>Verify the parts, not just the report<\/h3>\n<p>Check every repaired belt in the car. Each buckle should latch and release; a sharp tug should lock the retractor; the webbing should retract fully. Confirm there&#039;s no pretensioner code on the final scan. If any of these checks fail, the vehicle isn&#039;t ready for release.<\/p>\n<p>For the SRS, watch the warning lamp complete its bulb check and go out. Cycle the ignition and confirm the lamp stays off, then take a short drive when appropriate and check again. If a seat was removed, verify the passenger-airbag status with the seat empty and occupied. Follow the vehicle procedure for the occupancy check and keep people clear of the deployment path while working around restraint components.<\/p>\n<blockquote>\n<p>\u201cA scan without the saved post file is a scan the next shop can&#039;t trust.\u201d<\/p>\n<\/blockquote>\n<p>Make the release check simple enough to repeat on every ticket: the post-repair PDF is saved, the SRS lamp stays off after its bulb check, and the belts lock and retract correctly. If any item fails, hold the vehicle and resolve the problem before signing off.<\/p>\n<p><a id=\"what-to-do-when-crash-data-remains\"><\/a><\/p>\n<h2>What to Do When Crash Data Remains<\/h2>\n<p>Don&#039;t deliver the car on the strength of a dark airbag lamp if the final scan still shows crash data or a hard pretensioner fault. A clear command doesn&#039;t remove every stored deployment record. The original airbag control module or locked belt has to be repaired or replaced, installed correctly, and scanned again before the restraint system can pass.<\/p>\n<p><figure class=\"wp-block-image size-large\"><img decoding=\"async\" src=\"https:\/\/www.safetyrestore.com\/blog\/wp-content\/uploads\/2026\/11\/catalog-reference-image-3.jpg\" alt=\"SRS Airbag Module Reset\" \/><\/figure><\/p>\n<p>If the original module is being retained, the <a href=\"https:\/\/www.safetyrestore.com\/airbag-module-reset-service\/8-airbag-module-reset.html\">SRS airbag module reset service<\/a> addresses crash data and hard codes that dealers and ordinary OBD airbag scan tools can&#039;t reset. The <a href=\"https:\/\/www.safetyrestore.com\/68-airbag-module-reset.html\">SRS Airbag Module Reset<\/a> is a service to reset the airbag light after an accident by clearing crash data and hard codes in the SRS module. Safety Restore services customer-supplied removable modules and seat belts: customers select the quantity, place a repair order, ship the part, and receive it back after repair. No further programming is needed after the module reset; it comes back ready to install.<\/p>\n<p>Once the part is back, reconnect every seat and pretensioner plug, support the battery, and repeat the post repair scan. Save the clean report with the invoice. Don&#039;t treat the reset itself as the final check; the installed system still has to pass the vehicle-level scan and physical inspection.<\/p>\n<p>Release the vehicle only when the final report shows no current or crash DTCs, the SRS lamp completes its bulb check and stays off, and each retractor locks and releases without a pretensioner code. If crash data remains stored, send the affected module or belt for service before anyone calls the job done.<\/p>\n<hr>\n<p>Safety Restore repairs customer-supplied SRS modules and seat belt mechanisms for reinstallation after collision work. If crash data or a locked belt is holding up your post repair scan, visit <a href=\"https:\/\/safetyrestore.com\">Safety Restore<\/a> to review the relevant repair service.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>A car can look finished, drive straight, and have a dark airbag lamp while the SRS module still holds crash data. Before you hand back the keys, treat the post repair scan as proof that the affected systems work and the repair-related faults are resolved, not as a button to&hellip;<\/p>\n","protected":false},"author":1,"featured_media":36256,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"ngg_post_thumbnail":0,"footnotes":""},"categories":[3],"tags":[1405,1406,1403,768,1404],"class_list":["post-36257","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-seat-belt-repair","tag-airbag-codes","tag-obd-scan","tag-post-repair-scan","tag-seat-belt-reset","tag-srs-scan"],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v14.8.1 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>Post Repair Scan Steps for SRS Systems<\/title>\n<meta name=\"description\" content=\"Run a post repair scan after airbag or seat belt work: tools, steps, which codes to clear, and how to document a lamp that stays off.\" \/>\n<meta name=\"robots\" content=\"index, follow\" \/>\n<meta name=\"googlebot\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<meta name=\"bingbot\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Post Repair Scan Steps for SRS Systems\" \/>\n<meta property=\"og:description\" content=\"Run a post repair scan after airbag or seat belt work: tools, steps, which codes to clear, and how to document a lamp that stays off.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/\" \/>\n<meta property=\"og:site_name\" content=\"Safety Restore\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-21T09:56:03+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-11-21T09:56:17+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.safetyrestore.com\/blog\/wp-content\/uploads\/2026\/11\/post-repair-scan-auto-mechanic.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"1672\" \/>\n\t<meta property=\"og:image:height\" content=\"941\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"Organization\",\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/#organization\",\"name\":\"Safety Restore\",\"url\":\"https:\/\/www.safetyrestore.com\/blog\/\",\"sameAs\":[],\"logo\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/#logo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/www.safetyrestore.com\/blog\/wp-content\/uploads\/2020\/08\/logoc-1.svg\",\"caption\":\"Safety Restore\"},\"image\":{\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/#logo\"}},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/#website\",\"url\":\"https:\/\/www.safetyrestore.com\/blog\/\",\"name\":\"Safety Restore\",\"description\":\"Airbag Reset &amp; Seat Belt Replacement\/Repair\",\"publisher\":{\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":\"https:\/\/www.safetyrestore.com\/blog\/?s={search_term_string}\",\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/#primaryimage\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/www.safetyrestore.com\/blog\/wp-content\/uploads\/2026\/11\/post-repair-scan-auto-mechanic.jpg\",\"width\":1672,\"height\":941},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/#webpage\",\"url\":\"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/\",\"name\":\"Post Repair Scan Steps for SRS Systems\",\"isPartOf\":{\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/#primaryimage\"},\"datePublished\":\"2026-11-21T09:56:03+00:00\",\"dateModified\":\"2026-11-21T09:56:17+00:00\",\"description\":\"Run a post repair scan after airbag or seat belt work: tools, steps, which codes to clear, and how to document a lamp that stays off.\",\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/\"]}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/#article\",\"isPartOf\":{\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/#webpage\"},\"author\":{\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/#\/schema\/person\/d626451ed96030155b7c38dbda2948ce\"},\"headline\":\"Post Repair Scan Steps for SRS Systems\",\"datePublished\":\"2026-11-21T09:56:03+00:00\",\"dateModified\":\"2026-11-21T09:56:17+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/#webpage\"},\"publisher\":{\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/#organization\"},\"image\":{\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/post-repair-scan\/#primaryimage\"},\"keywords\":\"airbag codes,OBD scan,post repair scan,seat belt reset,SRS scan\",\"articleSection\":\"Seat Belt Repair\",\"inLanguage\":\"en-US\"},{\"@type\":\"Person\",\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/#\/schema\/person\/d626451ed96030155b7c38dbda2948ce\",\"name\":\"Artem Martynyuk\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/www.safetyrestore.com\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/secure.gravatar.com\/avatar\/78b2bd2931208418540957829b1d7c37a056b910a428cfb8ae33553eb5e86f4c?s=96&d=mm&r=g\",\"caption\":\"Artem Martynyuk\"}}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","_links":{"self":[{"href":"https:\/\/www.safetyrestore.com\/blog\/wp-json\/wp\/v2\/posts\/36257","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.safetyrestore.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.safetyrestore.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.safetyrestore.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.safetyrestore.com\/blog\/wp-json\/wp\/v2\/comments?post=36257"}],"version-history":[{"count":1,"href":"https:\/\/www.safetyrestore.com\/blog\/wp-json\/wp\/v2\/posts\/36257\/revisions"}],"predecessor-version":[{"id":36261,"href":"https:\/\/www.safetyrestore.com\/blog\/wp-json\/wp\/v2\/posts\/36257\/revisions\/36261"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.safetyrestore.com\/blog\/wp-json\/wp\/v2\/media\/36256"}],"wp:attachment":[{"href":"https:\/\/www.safetyrestore.com\/blog\/wp-json\/wp\/v2\/media?parent=36257"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.safetyrestore.com\/blog\/wp-json\/wp\/v2\/categories?post=36257"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.safetyrestore.com\/blog\/wp-json\/wp\/v2\/tags?post=36257"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}